DG series of copper wire drawing oil
The category :Copper Wire Drawing Oil Ordering hotline : 400-855-1230
Description
DG - 1 copper wire drawing oil
1. Product specifications:
DG - 1 # copper drawing lubricant, is my company introduction of German technology research and development of the latest generation of cooling lubricant. Mainly USES the synthetic grease, soap surfactants, infiltration agents, amide, antioxidants, anti-mold preservatives, defoaming agent and other additives, through the scientific method, the complex mixture, its various specifications are reaching or higher than the national standard.
Can control 8 mm - 2.6 mm of copper rod or copper wire, wire speed highest ≦ 25 m/s, this product has good oxidation resistance, lubricity, cleaning and the milk.
2. Technical requirements:
project | Quality indicators | The experimental method | |
Oil-based appearance | Orange red to palm red uniform fluid | visual | |
Kinematic viscosity (50 ℃), was/s not greater than | 115 | GB/T265 | |
The emulsification of 5% PH value | 7-9 | Enterprise standard | |
Since the emulsification | qualified | Enterprise standard | |
Condensation point ℃ | -5 | GB/T510 | |
5% emulsion corrosion test (55 + 2 ℃, full immersion copper T3 1 h) | qualified | Enterprise standard | |
Emulsion defoaming sex (50 + 2 ℃, 5 min) ml | ≦4 | Enterprise standard | |
Freezing and thawing test | qualified | Enterprise standard | |
5% emulsion stability (15 to 35 ℃) / 1 h. | Points of oil | No | Enterprise standard |
Soap volume % is not greater than | 2 | Enterprise standard | |
To adapt to the water hardness, mg when The amount per liter | No more than 1-6 | Enterprise standard |
3. Use the method and the matters needing attention:
1. The liquor should choose water or soft water.
2. The specific ratio of concentration and replacement should be depending on the different production process requirements, in use process, should be regularly refractometer or other methods to determine concentration and adjusted in a timely manner to add lubricant or water concentration meet the process requirements.
3. The ratio of emulsion: weight ratio: big: 3% ~ 7% : 2% ~ 6%
4. The emulsion using temperature should not be less than 25 ℃, should not be more than 55 ℃.
5. It is strictly prohibited to mixed with oil, acid emulsion, and effect use effect and service life.
6. During production, can not close the emulsion circulating stirring device, should maintain cycle, in case of emulsion metamorphic effect use effect. Replace the new liquid, emulsion pool and grooves must be removed.
7. Sealed storage at room temperature, the time limit is one year, continuous high temperature
4. safety and health:
Odor this product is non-toxic, no stimulation to skin, normal use harmless to the human body.
DG - 2 copper wire drawing oil
1. Product specifications:
DG - 2 # copper drawing lubricant, the introduction of German technology is my company developed the latest generation of cooling lubricant. Mainly with stable synthetic grease, surface active agent, complexing agent, fatty acid soap, infiltration agents, antioxidants, anti-mold preservatives, defoaming agent and other additives, through the scientific method, the complex mixture, its various specifications are reaching or higher than the national standard.
Can be drawn 3 mm - 0.08 mm copper wire, wire speed highest ≦ 35 m/s, this product has good oxidation resistance, lubricity, cleaning and the milk.
2. Technical requirements:
project | Quality indicators | The experimental method | |
Oil-based appearance | Orange red to palm red uniform fluid | visual | |
Kinematic viscosity (50 ℃), was/s not greater than | 116 | GB/T265 | |
The emulsification of 5% PH value | 7.2-9.2 | Enterprise standard | |
Since the emulsification | qualified | Enterprise standard | |
Condensation point ℃ | -5 | GB/T510 | |
5% emulsion corrosion test (55 + 2 ℃, full immersion copper T3 1 h) | qualified | Enterprise standard | |
Emulsion defoaming sex (50 + 2 ℃, 5 min) ml | ≦4 | Enterprise standard | |
Freezing and thawing test | qualified | Enterprise standard | |
5% emulsion stability (15 to 35 ℃) / 1 h. | Points of oil | No | Enterprise standard |
Soap volume % is not greater than | 2 | Enterprise standard | |
To adapt to the water hardness, mg when The amount per liter | No more than 1-5 | Enterprise standard |
3. Use the method and the matters needing attention:
1. The liquor should choose water or soft water.
2. The specific ratio of concentration and replacement should be depending on the different production process requirements, in use process, should be regularly refractometer or other methods to determine concentration and adjusted in a timely manner to add lubricant or water concentration meet the process requirements.
3. 3. The ratio of emulsion: weight ratio: : 2% ~ 6% : 1.5% ~ 3%
4. The emulsion using temperature should not be less than 30 ℃, should not be more than 55 ℃.
5. It is strictly prohibited to mixed with oil, acid emulsion, and effect use effect and service life.
6. During production, can not close the emulsion circulating stirring device, should maintain cycle, in case of emulsion metamorphic effect use effect. Replace the new liquid, emulsion pool and grooves must be removed.
7. Sealed storage at room temperature, the time limit is one year, continuous high temperature
4. safety and health:
Odor this product is non-toxic, no stimulation to skin, normal use harmless to the human body.
DG - 3 copper wire drawing oil
1. Product specifications:
DG - 3 # copper drawing lubricant, is my company introduction of German technology research and development of the latest generation of cooling lubricant. Mainly adopts advanced stable synthetic grease, surface active agent, complexing agent, amide soap, infiltration agents, antioxidants, anti-mold preservatives, net lotion, defoaming agent and other additives, through the scientific method, the complex mixture, its various specifications are reaching or higher than the national standard.
Can be drawn copper wire 0.8 mm - 0.05 mm, the highest line speed ≦ 38 m/s, this product has good oxidation resistance, lubricity, cleaning and the milk.
2. Technical requirements:
project | Quality indicators | The experimental method | |
Oil-based appearance | Orange red to palm red uniform fluid | visual | |
Kinematic viscosity (50 ℃), was/s not greater than | 118 | GB/T265 | |
The emulsification of 5% PH value | 7.2-9.2 | Enterprise standard | |
Since the emulsification | qualified | Enterprise standard | |
Condensation point ℃ | -5 | GB/T510 | |
5% emulsion corrosion test (55 + 2 ℃, full immersion copper T3 1 h) | qualified | Enterprise standard | |
Emulsion defoaming sex (50 + 2 ℃, 5 min) ml | ≦4 | Enterprise standard | |
Freezing and thawing test | qualified | Enterprise standard | |
5% emulsion stability (15 to 35 ℃) / 1 h. | Points of oil | No | Enterprise standard |
Soap volume % is not greater than | 1.8 | Enterprise standard | |
To adapt to the water hardness, mg when The amount per liter | No more than 1-5 | Enterprise standard |
3. Use the method and the matters needing attention:
1. The liquor should choose water or soft water.
2. The specific ratio of concentration and replacement should be depending on the different production process requirements, in use process, should be regularly refractometer or other methods to determine concentration and adjusted in a timely manner to add lubricant or water concentration meet the process requirements.
3. The ratio of emulsion: weight ratio: small: 1.5% ~ 3% : 0.8% ~ 1.8%
4. The emulsion using temperature should not be less than 30 ℃, should not be more than 55 ℃.
5. It is strictly prohibited to mixed with oil, acid emulsion, and effect use effect and service life.
6. During production, can not close the emulsion circulating stirring device, should maintain cycle, in case of emulsion metamorphic effect use effect. Replace the new liquid, emulsion pool and grooves must be removed.
7. Sealed storage at room temperature, the time limit is one year, continuous high temperature
4. safety and health:
Odor this product is non-toxic, no stimulation to skin, normal use harmless to the human body.
Changzhou Jiachen Oil Preparation Products Co., Ltd. Is the production of DG copper drawing lubricant, wire drawing lubricant professional factories, the company is willing to work with new and old customers at home and abroad wholeheartedly cooperation, mutual reciprocity and mutual benefit common development, welcome to contact us.